|
Pipe cutting machines
and devices |
|
WIDOS Pipe Cutter |
|
|
WIDOS pipe cutters with
cutter wheel and ratchet mechanism in 3 sizes 6
- 67 mm, 50 - 140 mm und 90 - 170 mm for a quick
and accurate cutting of PE pipes. |
 |
|
WIDOS Rotating Circular Saw |
|
|
Two types are available for
the cutting and bevelling of plastic pipes:
Model 315: OD 110 up to OD
315 mm
Model 500: OD 180 up to OD
500 mm
With this light
transportable machine plastic pipes of
polyolefine can be cut right-angled.
Cutting depth appr. 60 mm. |
 |
|
WIDOS Motor Hand Circular Saw with chain
driving |
|
|
The machine consists of a
motorized hand saw, 230 V/2200 W with guide
carriage and tensioning chain for each pipe
diameter. The tensioning chain is to be put
around the pipe and tightened by means of the
chain tensioner. The guidance vehicle is applied
with the hand circular saw. After turning on the
motor the saw is inserted. The pipe is then cut
by driving around.
A quick, clean and
right-angled cut is the result. Cutting depth up
to 60 mm with type 1 and up to 95 mm with type
2.
The easy handling despite
a high cutting speed and an optimal safety do
make the saw indispensable on each construction
site. Chains for standard pipes are available ex
warehouse. Special dimensions only on request. |
 |
|
WIDOS
Sawing System RS 315 |
|
|
The
band saw WIDOS RS 315 in extra-solid design has
been developed particularly for the exact
cutting of plastic pipes up to OD 315 and meets
highest requirements within modern production
lines.
The extremely solid saw bow
is optimized for operation with low vibration
and is driven on precise linear guides. The saw
band drive with high torque performance is
switched on over a push button and stops appr. 3
seconds after releasing the push button. The
complete saw bow is mounted on a high loadable
turning device angle indicator and can easily be
manually swivelled for up to 45° (67,5° on one
side) after being unlocked. The later course of
the cut is indicated by a line laser (optional
accessory).
The pipe support has an extremely solid
design so that even heaviest pieces can be
clamped safely and displaced with minimal
expenditure of force. The pipe is clamped by
means of a clamping belt, an initial adjusting
to the pipe dimension is not necessary. Pipe
clamping by means of a pneumatic cylinder is
possible on request. When using an optional
transverse support, a negative radial cut for
the fabrication of reduced branches at T- and Y-
pieces can be easily performed. The saw bow is
mounted on a basic plate, assembling works in
the workshop become unnecessary, only the
horizontal adjustment by means of adjusting
screws has to be carried out. |
|
|
WIDOS
Sawing Installation RS 630/800/1000/1200/1600* |
|
|
The
sawing installation RS in extra-solid design has
been developed particularly for the exact
cutting of plastic pipes and meets highest
requirements within modern production lines.
The extremely solid saw bow
is optimized for a low vibration and belt
sparing operation and is driven by hand wheel on
precise linear guides. The band drive with high
torque performance is equipped with a break so
that any after-running after switching off or
after pushing the emergency-off button is
avoided. The forward feed is secured against saw
forces being too high by means of a safety
clutch and totally insensitive to the produced
cuttings. The complete forward feed unit is
mounted on a high loadable live ring and can
easily be turned manually for 45° or 67,5° when
being unlocked. The band position and the set
angle are displayed on digital devices which can
be adjusted to zero very easily by means of
pneumatic centering devices.
The pipe supports have an extremely solid
design and are 1,8 m long on each side so that
even heaviest pieces can be clamped safely and
displaced on the exchangeable sliding coatings
with minimal expenditure of force. Extensions
for the pipe supports are available as option.
The pipes are clamped by means of a clamping
belt over the complete area to be worked, an
initial adjusting to the pipe dimension is not
necessary. When using an optional transverse
support in connection with an integrated turning
of the band and a digital display and locking of
the position, a negative radial cut for the
fabrication of reduced branches at T- and Y-
pieces can be easily performed. Due to the solid
base of the complete installation, assembling
works in the workshop become unnecessary, only
the horizontal adjustment by means of adjusting
screws has to be carried out.
* With all versions it is
possible to move the solid saw bow with a
motorized feed on precise linear guides. The
digital band index which is included indicates
the exact position of the saw band.
Attention! This supplement cannot be
subsequently built in. |
 |
|
WIDOS Pipe Cutter closed |
|
| WIDOS pipe cutters for
cutting off (90°) and chamfering (15°) of PVC,
PE, PP, VPE, PVDF and PB pipes up to OD 110 /
160.
Pipe cutter set 110:
Basic clamping OD 110, reduction inserts OD 50
and OD 75
Pipe cutter set 160:
Basic clamping OD 160, reduction inserts OD 110
and OD 125 |
No Picture Available |
